Total
635 CVE
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2022-50116 | 1 Linux | 1 Linux Kernel | 2025-11-18 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: tty: n_gsm: fix deadlock and link starvation in outgoing data path The current implementation queues up new control and user packets as needed and processes this queue down to the ldisc in the same code path. That means that the upper and the lower layer are hard coupled in the code. Due to this deadlocks can happen as seen below while transmitting data, especially during ldisc congestion. Furthermore, the data channels starve the control channel on high transmission load on the ldisc. Introduce an additional control channel data queue to prevent timeouts and link hangups during ldisc congestion. This is being processed before the user channel data queue in gsm_data_kick(), i.e. with the highest priority. Put the queue to ldisc data path into a workqueue and trigger it whenever new data has been put into the transmission queue. Change gsm_dlci_data_sweep() accordingly to fill up the transmission queue until TX_THRESH_HI. This solves the locking issue, keeps latency low and provides good performance on high data load. Note that now all packets from a DLCI are removed from the internal queue if the associated DLCI was closed. This ensures that no data is sent by the introduced write task to an already closed DLCI. BUG: spinlock recursion on CPU#0, test_v24_loop/124 lock: serial8250_ports+0x3a8/0x7500, .magic: dead4ead, .owner: test_v24_loop/124, .owner_cpu: 0 CPU: 0 PID: 124 Comm: test_v24_loop Tainted: G O 5.18.0-rc2 #3 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 Call Trace: <IRQ> dump_stack_lvl+0x34/0x44 do_raw_spin_lock+0x76/0xa0 _raw_spin_lock_irqsave+0x72/0x80 uart_write_room+0x3b/0xc0 gsm_data_kick+0x14b/0x240 [n_gsm] gsmld_write_wakeup+0x35/0x70 [n_gsm] tty_wakeup+0x53/0x60 tty_port_default_wakeup+0x1b/0x30 serial8250_tx_chars+0x12f/0x220 serial8250_handle_irq.part.0+0xfe/0x150 serial8250_default_handle_irq+0x48/0x80 serial8250_interrupt+0x56/0xa0 __handle_irq_event_percpu+0x78/0x1f0 handle_irq_event+0x34/0x70 handle_fasteoi_irq+0x90/0x1e0 __common_interrupt+0x69/0x100 common_interrupt+0x48/0xc0 asm_common_interrupt+0x1e/0x40 RIP: 0010:__do_softirq+0x83/0x34e Code: 2a 0a ff 0f b7 ed c7 44 24 10 0a 00 00 00 48 c7 c7 51 2a 64 82 e8 2d e2 d5 ff 65 66 c7 05 83 af 1e 7e 00 00 fb b8 ff ff ff ff <49> c7 c2 40 61 80 82 0f bc c5 41 89 c4 41 83 c4 01 0f 84 e6 00 00 RSP: 0018:ffffc90000003f98 EFLAGS: 00000286 RAX: 00000000ffffffff RBX: 0000000000000000 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffffffff82642a51 RDI: ffffffff825bb5e7 RBP: 0000000000000200 R08: 00000008de3271a8 R09: 0000000000000000 R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000000 R13: 0000000000000030 R14: 0000000000000000 R15: 0000000000000000 ? __do_softirq+0x73/0x34e irq_exit_rcu+0xb5/0x100 common_interrupt+0xa4/0xc0 </IRQ> <TASK> asm_common_interrupt+0x1e/0x40 RIP: 0010:_raw_spin_unlock_irqrestore+0x2e/0x50 Code: 00 55 48 89 fd 48 83 c7 18 53 48 89 f3 48 8b 74 24 10 e8 85 28 36 ff 48 89 ef e8 cd 58 36 ff 80 e7 02 74 01 fb bf 01 00 00 00 <e8> 3d 97 33 ff 65 8b 05 96 23 2b 7e 85 c0 74 03 5b 5d c3 0f 1f 44 RSP: 0018:ffffc9000020fd08 EFLAGS: 00000202 RAX: 0000000000000000 RBX: 0000000000000246 RCX: 0000000000000000 RDX: 0000000000000004 RSI: ffffffff8257fd74 RDI: 0000000000000001 RBP: ffff8880057de3a0 R08: 00000008de233000 R09: 0000000000000000 R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000000 R13: 0000000000000100 R14: 0000000000000202 R15: ffff8880057df0b8 ? _raw_spin_unlock_irqrestore+0x23/0x50 gsmtty_write+0x65/0x80 [n_gsm] n_tty_write+0x33f/0x530 ? swake_up_all+0xe0/0xe0 file_tty_write.constprop.0+0x1b1/0x320 ? n_tty_flush_buffer+0xb0/0xb0 new_sync_write+0x10c/0x190 vfs_write+0x282/0x310 ksys_write+0x68/0xe0 do_syscall_64+0x3b/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f3e5e35c15c Code: 8b 7c 24 08 89 c5 e8 c5 ff ff ff 89 ef 89 44 24 ---truncated--- | ||||
| CVE-2025-38551 | 1 Linux | 1 Linux Kernel | 2025-11-18 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: virtio-net: fix recursived rtnl_lock() during probe() The deadlock appears in a stack trace like: virtnet_probe() rtnl_lock() virtio_config_changed_work() netdev_notify_peers() rtnl_lock() It happens if the VMM sends a VIRTIO_NET_S_ANNOUNCE request while the virtio-net driver is still probing. The config_work in probe() will get scheduled until virtnet_open() enables the config change notification via virtio_config_driver_enable(). | ||||
| CVE-2025-38311 | 1 Linux | 1 Linux Kernel | 2025-11-18 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: iavf: get rid of the crit lock Get rid of the crit lock. That frees us from the error prone logic of try_locks. Thanks to netdev_lock() by Jakub it is now easy, and in most cases we were protected by it already - replace crit lock by netdev lock when it was not the case. Lockdep reports that we should cancel the work under crit_lock [splat1], and that was the scheme we have mostly followed since [1] by Slawomir. But when that is done we still got into deadlocks [splat2]. So instead we should look at the bigger problem, namely "weird locking/scheduling" of the iavf. The first step to fix that is to remove the crit lock. I will followup with a -next series that simplifies scheduling/tasks. Cancel the work without netdev lock (weird unlock+lock scheme), to fix the [splat2] (which would be totally ugly if we would kept the crit lock). Extend protected part of iavf_watchdog_task() to include scheduling more work. Note that the removed comment in iavf_reset_task() was misplaced, it belonged to inside of the removed if condition, so it's gone now. [splat1] - w/o this patch - The deadlock during VF removal: WARNING: possible circular locking dependency detected sh/3825 is trying to acquire lock: ((work_completion)(&(&adapter->watchdog_task)->work)){+.+.}-{0:0}, at: start_flush_work+0x1a1/0x470 but task is already holding lock: (&adapter->crit_lock){+.+.}-{4:4}, at: iavf_remove+0xd1/0x690 [iavf] which lock already depends on the new lock. [splat2] - when cancelling work under crit lock, w/o this series, see [2] for the band aid attempt WARNING: possible circular locking dependency detected sh/3550 is trying to acquire lock: ((wq_completion)iavf){+.+.}-{0:0}, at: touch_wq_lockdep_map+0x26/0x90 but task is already holding lock: (&dev->lock){+.+.}-{4:4}, at: iavf_remove+0xa6/0x6e0 [iavf] which lock already depends on the new lock. [1] fc2e6b3b132a ("iavf: Rework mutexes for better synchronisation") [2] https://github.com/pkitszel/linux/commit/52dddbfc2bb60294083f5711a158a | ||||
| CVE-2025-38353 | 1 Linux | 1 Linux Kernel | 2025-11-18 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: drm/xe: Fix taking invalid lock on wedge If device wedges on e.g. GuC upload, the submission is not yet enabled and the state is not even initialized. Protect the wedge call so it does nothing in this case. It fixes the following splat: [] xe 0000:bf:00.0: [drm] device wedged, needs recovery [] ------------[ cut here ]------------ [] DEBUG_LOCKS_WARN_ON(lock->magic != lock) [] WARNING: CPU: 48 PID: 312 at kernel/locking/mutex.c:564 __mutex_lock+0x8a1/0xe60 ... [] RIP: 0010:__mutex_lock+0x8a1/0xe60 [] mutex_lock_nested+0x1b/0x30 [] xe_guc_submit_wedge+0x80/0x2b0 [xe] | ||||
| CVE-2022-50149 | 1 Linux | 1 Linux Kernel | 2025-11-17 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: driver core: fix potential deadlock in __driver_attach In __driver_attach function, There are also AA deadlock problem, like the commit b232b02bf3c2 ("driver core: fix deadlock in __device_attach"). stack like commit b232b02bf3c2 ("driver core: fix deadlock in __device_attach"). list below: In __driver_attach function, The lock holding logic is as follows: ... __driver_attach if (driver_allows_async_probing(drv)) device_lock(dev) // get lock dev async_schedule_dev(__driver_attach_async_helper, dev); // func async_schedule_node async_schedule_node_domain(func) entry = kzalloc(sizeof(struct async_entry), GFP_ATOMIC); /* when fail or work limit, sync to execute func, but __driver_attach_async_helper will get lock dev as will, which will lead to A-A deadlock. */ if (!entry || atomic_read(&entry_count) > MAX_WORK) { func; else queue_work_node(node, system_unbound_wq, &entry->work) device_unlock(dev) As above show, when it is allowed to do async probes, because of out of memory or work limit, async work is not be allowed, to do sync execute instead. it will lead to A-A deadlock because of __driver_attach_async_helper getting lock dev. Reproduce: and it can be reproduce by make the condition (if (!entry || atomic_read(&entry_count) > MAX_WORK)) untenable, like below: [ 370.785650] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 370.787154] task:swapper/0 state:D stack: 0 pid: 1 ppid: 0 flags:0x00004000 [ 370.788865] Call Trace: [ 370.789374] <TASK> [ 370.789841] __schedule+0x482/0x1050 [ 370.790613] schedule+0x92/0x1a0 [ 370.791290] schedule_preempt_disabled+0x2c/0x50 [ 370.792256] __mutex_lock.isra.0+0x757/0xec0 [ 370.793158] __mutex_lock_slowpath+0x1f/0x30 [ 370.794079] mutex_lock+0x50/0x60 [ 370.794795] __device_driver_lock+0x2f/0x70 [ 370.795677] ? driver_probe_device+0xd0/0xd0 [ 370.796576] __driver_attach_async_helper+0x1d/0xd0 [ 370.797318] ? driver_probe_device+0xd0/0xd0 [ 370.797957] async_schedule_node_domain+0xa5/0xc0 [ 370.798652] async_schedule_node+0x19/0x30 [ 370.799243] __driver_attach+0x246/0x290 [ 370.799828] ? driver_allows_async_probing+0xa0/0xa0 [ 370.800548] bus_for_each_dev+0x9d/0x130 [ 370.801132] driver_attach+0x22/0x30 [ 370.801666] bus_add_driver+0x290/0x340 [ 370.802246] driver_register+0x88/0x140 [ 370.802817] ? virtio_scsi_init+0x116/0x116 [ 370.803425] scsi_register_driver+0x1a/0x30 [ 370.804057] init_sd+0x184/0x226 [ 370.804533] do_one_initcall+0x71/0x3a0 [ 370.805107] kernel_init_freeable+0x39a/0x43a [ 370.805759] ? rest_init+0x150/0x150 [ 370.806283] kernel_init+0x26/0x230 [ 370.806799] ret_from_fork+0x1f/0x30 To fix the deadlock, move the async_schedule_dev outside device_lock, as we can see, in async_schedule_node_domain, the parameter of queue_work_node is system_unbound_wq, so it can accept concurrent operations. which will also not change the code logic, and will not lead to deadlock. | ||||
| CVE-2022-50166 | 1 Linux | 1 Linux Kernel | 2025-11-17 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: Bluetooth: When HCI work queue is drained, only queue chained work The HCI command, event, and data packet processing workqueue is drained to avoid deadlock in commit 76727c02c1e1 ("Bluetooth: Call drain_workqueue() before resetting state"). There is another delayed work, which will queue command to this drained workqueue. Which results in the following error report: Bluetooth: hci2: command 0x040f tx timeout WARNING: CPU: 1 PID: 18374 at kernel/workqueue.c:1438 __queue_work+0xdad/0x1140 Workqueue: events hci_cmd_timeout RIP: 0010:__queue_work+0xdad/0x1140 RSP: 0000:ffffc90002cffc60 EFLAGS: 00010093 RAX: 0000000000000000 RBX: ffff8880b9d3ec00 RCX: 0000000000000000 RDX: ffff888024ba0000 RSI: ffffffff814e048d RDI: ffff8880b9d3ec08 RBP: 0000000000000008 R08: 0000000000000000 R09: 00000000b9d39700 R10: ffffffff814f73c6 R11: 0000000000000000 R12: ffff88807cce4c60 R13: 0000000000000000 R14: ffff8880796d8800 R15: ffff8880796d8800 FS: 0000000000000000(0000) GS:ffff8880b9d00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000000c0174b4000 CR3: 000000007cae9000 CR4: 00000000003506e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> ? queue_work_on+0xcb/0x110 ? lockdep_hardirqs_off+0x90/0xd0 queue_work_on+0xee/0x110 process_one_work+0x996/0x1610 ? pwq_dec_nr_in_flight+0x2a0/0x2a0 ? rwlock_bug.part.0+0x90/0x90 ? _raw_spin_lock_irq+0x41/0x50 worker_thread+0x665/0x1080 ? process_one_work+0x1610/0x1610 kthread+0x2e9/0x3a0 ? kthread_complete_and_exit+0x40/0x40 ret_from_fork+0x1f/0x30 </TASK> To fix this, we can add a new HCI_DRAIN_WQ flag, and don't queue the timeout workqueue while command workqueue is draining. | ||||
| CVE-2025-37907 | 1 Linux | 1 Linux Kernel | 2025-11-17 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: accel/ivpu: Fix locking order in ivpu_job_submit Fix deadlock in job submission and abort handling. When a thread aborts currently executing jobs due to a fault, it first locks the global lock protecting submitted_jobs (#1). After the last job is destroyed, it proceeds to release the related context and locks file_priv (#2). Meanwhile, in the job submission thread, the file_priv lock (#2) is taken first, and then the submitted_jobs lock (#1) is obtained when a job is added to the submitted jobs list. CPU0 CPU1 ---- ---- (for example due to a fault) (jobs submissions keep coming) lock(&vdev->submitted_jobs_lock) #1 ivpu_jobs_abort_all() job_destroy() lock(&file_priv->lock) #2 lock(&vdev->submitted_jobs_lock) #1 file_priv_release() lock(&vdev->context_list_lock) lock(&file_priv->lock) #2 This order of locking causes a deadlock. To resolve this issue, change the order of locking in ivpu_job_submit(). | ||||
| CVE-2025-37847 | 1 Linux | 1 Linux Kernel | 2025-11-17 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: accel/ivpu: Fix deadlock in ivpu_ms_cleanup() Fix deadlock in ivpu_ms_cleanup() by preventing runtime resume after file_priv->ms_lock is acquired. During a failure in runtime resume, a cold boot is executed, which calls ivpu_ms_cleanup_all(). This function calls ivpu_ms_cleanup() that acquires file_priv->ms_lock and causes the deadlock. | ||||
| CVE-2025-37848 | 1 Linux | 1 Linux Kernel | 2025-11-17 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: accel/ivpu: Fix PM related deadlocks in MS IOCTLs Prevent runtime resume/suspend while MS IOCTLs are in progress. Failed suspend will call ivpu_ms_cleanup() that would try to acquire file_priv->ms_lock, which is already held by the IOCTLs. | ||||
| CVE-2025-37843 | 1 Linux | 1 Linux Kernel | 2025-11-17 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: PCI: pciehp: Avoid unnecessary device replacement check Hot-removal of nested PCI hotplug ports suffers from a long-standing race condition which can lead to a deadlock: A parent hotplug port acquires pci_lock_rescan_remove(), then waits for pciehp to unbind from a child hotplug port. Meanwhile that child hotplug port tries to acquire pci_lock_rescan_remove() as well in order to remove its own children. The deadlock only occurs if the parent acquires pci_lock_rescan_remove() first, not if the child happens to acquire it first. Several workarounds to avoid the issue have been proposed and discarded over the years, e.g.: https://lore.kernel.org/r/4c882e25194ba8282b78fe963fec8faae7cf23eb.1529173804.git.lukas@wunner.de/ A proper fix is being worked on, but needs more time as it is nontrivial and necessarily intrusive. Recent commit 9d573d19547b ("PCI: pciehp: Detect device replacement during system sleep") provokes more frequent occurrence of the deadlock when removing more than one Thunderbolt device during system sleep. The commit sought to detect device replacement, but also triggered on device removal. Differentiating reliably between replacement and removal is impossible because pci_get_dsn() returns 0 both if the device was removed, as well as if it was replaced with one lacking a Device Serial Number. Avoid the more frequent occurrence of the deadlock by checking whether the hotplug port itself was hot-removed. If so, there's no sense in checking whether its child device was replaced. This works because the ->resume_noirq() callback is invoked in top-down order for the entire hierarchy: A parent hotplug port detecting device replacement (or removal) marks all children as removed using pci_dev_set_disconnected() and a child hotplug port can then reliably detect being removed. | ||||
| CVE-2022-49943 | 1 Linux | 1 Linux Kernel | 2025-11-14 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: USB: gadget: Fix obscure lockdep violation for udc_mutex A recent commit expanding the scope of the udc_lock mutex in the gadget core managed to cause an obscure and slightly bizarre lockdep violation. In abbreviated form: ====================================================== WARNING: possible circular locking dependency detected 5.19.0-rc7+ #12510 Not tainted ------------------------------------------------------ udevadm/312 is trying to acquire lock: ffff80000aae1058 (udc_lock){+.+.}-{3:3}, at: usb_udc_uevent+0x54/0xe0 but task is already holding lock: ffff000002277548 (kn->active#4){++++}-{0:0}, at: kernfs_seq_start+0x34/0xe0 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #3 (kn->active#4){++++}-{0:0}: lock_acquire+0x68/0x84 __kernfs_remove+0x268/0x380 kernfs_remove_by_name_ns+0x58/0xac sysfs_remove_file_ns+0x18/0x24 device_del+0x15c/0x440 -> #2 (device_links_lock){+.+.}-{3:3}: lock_acquire+0x68/0x84 __mutex_lock+0x9c/0x430 mutex_lock_nested+0x38/0x64 device_link_remove+0x3c/0xa0 _regulator_put.part.0+0x168/0x190 regulator_put+0x3c/0x54 devm_regulator_release+0x14/0x20 -> #1 (regulator_list_mutex){+.+.}-{3:3}: lock_acquire+0x68/0x84 __mutex_lock+0x9c/0x430 mutex_lock_nested+0x38/0x64 regulator_lock_dependent+0x54/0x284 regulator_enable+0x34/0x80 phy_power_on+0x24/0x130 __dwc2_lowlevel_hw_enable+0x100/0x130 dwc2_lowlevel_hw_enable+0x18/0x40 dwc2_hsotg_udc_start+0x6c/0x2f0 gadget_bind_driver+0x124/0x1f4 -> #0 (udc_lock){+.+.}-{3:3}: __lock_acquire+0x1298/0x20cc lock_acquire.part.0+0xe0/0x230 lock_acquire+0x68/0x84 __mutex_lock+0x9c/0x430 mutex_lock_nested+0x38/0x64 usb_udc_uevent+0x54/0xe0 Evidently this was caused by the scope of udc_mutex being too large. The mutex is only meant to protect udc->driver along with a few other things. As far as I can tell, there's no reason for the mutex to be held while the gadget core calls a gadget driver's ->bind or ->unbind routine, or while a UDC is being started or stopped. (This accounts for link #1 in the chain above, where the mutex is held while the dwc2_hsotg_udc is started as part of driver probing.) Gadget drivers' ->disconnect callbacks are problematic. Even though usb_gadget_disconnect() will now acquire the udc_mutex, there's a window in usb_gadget_bind_driver() between the times when the mutex is released and the ->bind callback is invoked. If a disconnect occurred during that window, we could call the driver's ->disconnect routine before its ->bind routine. To prevent this from happening, it will be necessary to prevent a UDC from connecting while it has no gadget driver. This should be done already but it doesn't seem to be; currently usb_gadget_connect() has no check for this. Such a check will have to be added later. Some degree of mutual exclusion is required in soft_connect_store(), which can dereference udc->driver at arbitrary times since it is a sysfs callback. The solution here is to acquire the gadget's device lock rather than the udc_mutex. Since the driver core guarantees that the device lock is always held during driver binding and unbinding, this will make the accesses in soft_connect_store() mutually exclusive with any changes to udc->driver. Lastly, it turns out there is one place which should hold the udc_mutex but currently does not: The function_show() routine needs protection while it dereferences udc->driver. The missing lock and unlock calls are added. | ||||
| CVE-2022-49986 | 1 Linux | 1 Linux Kernel | 2025-11-14 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: scsi: storvsc: Remove WQ_MEM_RECLAIM from storvsc_error_wq storvsc_error_wq workqueue should not be marked as WQ_MEM_RECLAIM as it doesn't need to make forward progress under memory pressure. Marking this workqueue as WQ_MEM_RECLAIM may cause deadlock while flushing a non-WQ_MEM_RECLAIM workqueue. In the current state it causes the following warning: [ 14.506347] ------------[ cut here ]------------ [ 14.506354] workqueue: WQ_MEM_RECLAIM storvsc_error_wq_0:storvsc_remove_lun is flushing !WQ_MEM_RECLAIM events_freezable_power_:disk_events_workfn [ 14.506360] WARNING: CPU: 0 PID: 8 at <-snip->kernel/workqueue.c:2623 check_flush_dependency+0xb5/0x130 [ 14.506390] CPU: 0 PID: 8 Comm: kworker/u4:0 Not tainted 5.4.0-1086-azure #91~18.04.1-Ubuntu [ 14.506391] Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS Hyper-V UEFI Release v4.1 05/09/2022 [ 14.506393] Workqueue: storvsc_error_wq_0 storvsc_remove_lun [ 14.506395] RIP: 0010:check_flush_dependency+0xb5/0x130 <-snip-> [ 14.506408] Call Trace: [ 14.506412] __flush_work+0xf1/0x1c0 [ 14.506414] __cancel_work_timer+0x12f/0x1b0 [ 14.506417] ? kernfs_put+0xf0/0x190 [ 14.506418] cancel_delayed_work_sync+0x13/0x20 [ 14.506420] disk_block_events+0x78/0x80 [ 14.506421] del_gendisk+0x3d/0x2f0 [ 14.506423] sr_remove+0x28/0x70 [ 14.506427] device_release_driver_internal+0xef/0x1c0 [ 14.506428] device_release_driver+0x12/0x20 [ 14.506429] bus_remove_device+0xe1/0x150 [ 14.506431] device_del+0x167/0x380 [ 14.506432] __scsi_remove_device+0x11d/0x150 [ 14.506433] scsi_remove_device+0x26/0x40 [ 14.506434] storvsc_remove_lun+0x40/0x60 [ 14.506436] process_one_work+0x209/0x400 [ 14.506437] worker_thread+0x34/0x400 [ 14.506439] kthread+0x121/0x140 [ 14.506440] ? process_one_work+0x400/0x400 [ 14.506441] ? kthread_park+0x90/0x90 [ 14.506443] ret_from_fork+0x35/0x40 [ 14.506445] ---[ end trace 2d9633159fdc6ee7 ]--- | ||||
| CVE-2022-49998 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2025-11-14 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: rxrpc: Fix locking in rxrpc's sendmsg Fix three bugs in the rxrpc's sendmsg implementation: (1) rxrpc_new_client_call() should release the socket lock when returning an error from rxrpc_get_call_slot(). (2) rxrpc_wait_for_tx_window_intr() will return without the call mutex held in the event that we're interrupted by a signal whilst waiting for tx space on the socket or relocking the call mutex afterwards. Fix this by: (a) moving the unlock/lock of the call mutex up to rxrpc_send_data() such that the lock is not held around all of rxrpc_wait_for_tx_window*() and (b) indicating to higher callers whether we're return with the lock dropped. Note that this means recvmsg() will not block on this call whilst we're waiting. (3) After dropping and regaining the call mutex, rxrpc_send_data() needs to go and recheck the state of the tx_pending buffer and the tx_total_len check in case we raced with another sendmsg() on the same call. Thinking on this some more, it might make sense to have different locks for sendmsg() and recvmsg(). There's probably no need to make recvmsg() wait for sendmsg(). It does mean that recvmsg() can return MSG_EOR indicating that a call is dead before a sendmsg() to that call returns - but that can currently happen anyway. Without fix (2), something like the following can be induced: WARNING: bad unlock balance detected! 5.16.0-rc6-syzkaller #0 Not tainted ------------------------------------- syz-executor011/3597 is trying to release lock (&call->user_mutex) at: [<ffffffff885163a3>] rxrpc_do_sendmsg+0xc13/0x1350 net/rxrpc/sendmsg.c:748 but there are no more locks to release! other info that might help us debug this: no locks held by syz-executor011/3597. ... Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106 print_unlock_imbalance_bug include/trace/events/lock.h:58 [inline] __lock_release kernel/locking/lockdep.c:5306 [inline] lock_release.cold+0x49/0x4e kernel/locking/lockdep.c:5657 __mutex_unlock_slowpath+0x99/0x5e0 kernel/locking/mutex.c:900 rxrpc_do_sendmsg+0xc13/0x1350 net/rxrpc/sendmsg.c:748 rxrpc_sendmsg+0x420/0x630 net/rxrpc/af_rxrpc.c:561 sock_sendmsg_nosec net/socket.c:704 [inline] sock_sendmsg+0xcf/0x120 net/socket.c:724 ____sys_sendmsg+0x6e8/0x810 net/socket.c:2409 ___sys_sendmsg+0xf3/0x170 net/socket.c:2463 __sys_sendmsg+0xe5/0x1b0 net/socket.c:2492 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x44/0xae [Thanks to Hawkins Jiawei and Khalid Masum for their attempts to fix this] | ||||
| CVE-2025-63396 | 1 Pytorch | 1 Pytorch | 2025-11-14 | 3.3 Low |
| An issue was discovered in PyTorch v2.5 and v2.7.1. Omission of profiler.stop() can cause torch.profiler.profile (PythonTracer) to crash or hang during finalization, leading to a Denial of Service (DoS). | ||||
| CVE-2022-50045 | 1 Linux | 1 Linux Kernel | 2025-11-13 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: powerpc/pci: Fix get_phb_number() locking The recent change to get_phb_number() causes a DEBUG_ATOMIC_SLEEP warning on some systems: BUG: sleeping function called from invalid context at kernel/locking/mutex.c:580 in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 1, name: swapper preempt_count: 1, expected: 0 RCU nest depth: 0, expected: 0 1 lock held by swapper/1: #0: c157efb0 (hose_spinlock){+.+.}-{2:2}, at: pcibios_alloc_controller+0x64/0x220 Preemption disabled at: [<00000000>] 0x0 CPU: 0 PID: 1 Comm: swapper Not tainted 5.19.0-yocto-standard+ #1 Call Trace: [d101dc90] [c073b264] dump_stack_lvl+0x50/0x8c (unreliable) [d101dcb0] [c0093b70] __might_resched+0x258/0x2a8 [d101dcd0] [c0d3e634] __mutex_lock+0x6c/0x6ec [d101dd50] [c0a84174] of_alias_get_id+0x50/0xf4 [d101dd80] [c002ec78] pcibios_alloc_controller+0x1b8/0x220 [d101ddd0] [c140c9dc] pmac_pci_init+0x198/0x784 [d101de50] [c140852c] discover_phbs+0x30/0x4c [d101de60] [c0007fd4] do_one_initcall+0x94/0x344 [d101ded0] [c1403b40] kernel_init_freeable+0x1a8/0x22c [d101df10] [c00086e0] kernel_init+0x34/0x160 [d101df30] [c001b334] ret_from_kernel_thread+0x5c/0x64 This is because pcibios_alloc_controller() holds hose_spinlock but of_alias_get_id() takes of_mutex which can sleep. The hose_spinlock protects the phb_bitmap, and also the hose_list, but it doesn't need to be held while get_phb_number() calls the OF routines, because those are only looking up information in the device tree. So fix it by having get_phb_number() take the hose_spinlock itself, only where required, and then dropping the lock before returning. pcibios_alloc_controller() then needs to take the lock again before the list_add() but that's safe, the order of the list is not important. | ||||
| CVE-2022-50053 | 1 Linux | 1 Linux Kernel | 2025-11-13 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: iavf: Fix reset error handling Do not call iavf_close in iavf_reset_task error handling. Doing so can lead to double call of napi_disable, which can lead to deadlock there. Removing VF would lead to iavf_remove task being stuck, because it requires crit_lock, which is held by iavf_close. Call iavf_disable_vf if reset fail, so that driver will clean up remaining invalid resources. During rapid VF resets, HW can fail to setup VF mailbox. Wrong error handling can lead to iavf_remove being stuck with: [ 5218.999087] iavf 0000:82:01.0: Failed to init adminq: -53 ... [ 5267.189211] INFO: task repro.sh:11219 blocked for more than 30 seconds. [ 5267.189520] Tainted: G S E 5.18.0-04958-ga54ce3703613-dirty #1 [ 5267.189764] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 5267.190062] task:repro.sh state:D stack: 0 pid:11219 ppid: 8162 flags:0x00000000 [ 5267.190347] Call Trace: [ 5267.190647] <TASK> [ 5267.190927] __schedule+0x460/0x9f0 [ 5267.191264] schedule+0x44/0xb0 [ 5267.191563] schedule_preempt_disabled+0x14/0x20 [ 5267.191890] __mutex_lock.isra.12+0x6e3/0xac0 [ 5267.192237] ? iavf_remove+0xf9/0x6c0 [iavf] [ 5267.192565] iavf_remove+0x12a/0x6c0 [iavf] [ 5267.192911] ? _raw_spin_unlock_irqrestore+0x1e/0x40 [ 5267.193285] pci_device_remove+0x36/0xb0 [ 5267.193619] device_release_driver_internal+0xc1/0x150 [ 5267.193974] pci_stop_bus_device+0x69/0x90 [ 5267.194361] pci_stop_and_remove_bus_device+0xe/0x20 [ 5267.194735] pci_iov_remove_virtfn+0xba/0x120 [ 5267.195130] sriov_disable+0x2f/0xe0 [ 5267.195506] ice_free_vfs+0x7d/0x2f0 [ice] [ 5267.196056] ? pci_get_device+0x4f/0x70 [ 5267.196496] ice_sriov_configure+0x78/0x1a0 [ice] [ 5267.196995] sriov_numvfs_store+0xfe/0x140 [ 5267.197466] kernfs_fop_write_iter+0x12e/0x1c0 [ 5267.197918] new_sync_write+0x10c/0x190 [ 5267.198404] vfs_write+0x24e/0x2d0 [ 5267.198886] ksys_write+0x5c/0xd0 [ 5267.199367] do_syscall_64+0x3a/0x80 [ 5267.199827] entry_SYSCALL_64_after_hwframe+0x46/0xb0 [ 5267.200317] RIP: 0033:0x7f5b381205c8 [ 5267.200814] RSP: 002b:00007fff8c7e8c78 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 [ 5267.201981] RAX: ffffffffffffffda RBX: 0000000000000002 RCX: 00007f5b381205c8 [ 5267.202620] RDX: 0000000000000002 RSI: 00005569420ee900 RDI: 0000000000000001 [ 5267.203426] RBP: 00005569420ee900 R08: 000000000000000a R09: 00007f5b38180820 [ 5267.204327] R10: 000000000000000a R11: 0000000000000246 R12: 00007f5b383c06e0 [ 5267.205193] R13: 0000000000000002 R14: 00007f5b383bb880 R15: 0000000000000002 [ 5267.206041] </TASK> [ 5267.206970] Kernel panic - not syncing: hung_task: blocked tasks [ 5267.207809] CPU: 48 PID: 551 Comm: khungtaskd Kdump: loaded Tainted: G S E 5.18.0-04958-ga54ce3703613-dirty #1 [ 5267.208726] Hardware name: Dell Inc. PowerEdge R730/0WCJNT, BIOS 2.11.0 11/02/2019 [ 5267.209623] Call Trace: [ 5267.210569] <TASK> [ 5267.211480] dump_stack_lvl+0x33/0x42 [ 5267.212472] panic+0x107/0x294 [ 5267.213467] watchdog.cold.8+0xc/0xbb [ 5267.214413] ? proc_dohung_task_timeout_secs+0x30/0x30 [ 5267.215511] kthread+0xf4/0x120 [ 5267.216459] ? kthread_complete_and_exit+0x20/0x20 [ 5267.217505] ret_from_fork+0x22/0x30 [ 5267.218459] </TASK> | ||||
| CVE-2025-37812 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2025-11-12 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: usb: cdns3: Fix deadlock when using NCM gadget The cdns3 driver has the same NCM deadlock as fixed in cdnsp by commit 58f2fcb3a845 ("usb: cdnsp: Fix deadlock issue during using NCM gadget"). Under PREEMPT_RT the deadlock can be readily triggered by heavy network traffic, for example using "iperf --bidir" over NCM ethernet link. The deadlock occurs because the threaded interrupt handler gets preempted by a softirq, but both are protected by the same spinlock. Prevent deadlock by disabling softirq during threaded irq handler. | ||||
| CVE-2025-37868 | 1 Linux | 1 Linux Kernel | 2025-11-12 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: drm/xe/userptr: fix notifier vs folio deadlock User is reporting what smells like notifier vs folio deadlock, where migrate_pages_batch() on core kernel side is holding folio lock(s) and then interacting with the mappings of it, however those mappings are tied to some userptr, which means calling into the notifier callback and grabbing the notifier lock. With perfect timing it looks possible that the pages we pulled from the hmm fault can get sniped by migrate_pages_batch() at the same time that we are holding the notifier lock to mark the pages as accessed/dirty, but at this point we also want to grab the folio locks(s) to mark them as dirty, but if they are contended from notifier/migrate_pages_batch side then we deadlock since folio lock won't be dropped until we drop the notifier lock. Fortunately the mark_page_accessed/dirty is not really needed in the first place it seems and should have already been done by hmm fault, so just remove it. (cherry picked from commit bd7c0cb695e87c0e43247be8196b4919edbe0e85) | ||||
| CVE-2025-37880 | 1 Linux | 1 Linux Kernel | 2025-11-12 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: um: work around sched_yield not yielding in time-travel mode sched_yield by a userspace may not actually cause scheduling in time-travel mode as no time has passed. In the case seen it appears to be a badly implemented userspace spinlock in ASAN. Unfortunately, with time-travel it causes an extreme slowdown or even deadlock depending on the kernel configuration (CONFIG_UML_MAX_USERSPACE_ITERATIONS). Work around it by accounting time to the process whenever it executes a sched_yield syscall. | ||||
| CVE-2025-37884 | 2 Debian, Linux | 2 Debian Linux, Linux Kernel | 2025-11-12 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: bpf: Fix deadlock between rcu_tasks_trace and event_mutex. Fix the following deadlock: CPU A _free_event() perf_kprobe_destroy() mutex_lock(&event_mutex) perf_trace_event_unreg() synchronize_rcu_tasks_trace() There are several paths where _free_event() grabs event_mutex and calls sync_rcu_tasks_trace. Above is one such case. CPU B bpf_prog_test_run_syscall() rcu_read_lock_trace() bpf_prog_run_pin_on_cpu() bpf_prog_load() bpf_tracing_func_proto() trace_set_clr_event() mutex_lock(&event_mutex) Delegate trace_set_clr_event() to workqueue to avoid such lock dependency. | ||||